LoresonDE
Well-Known Member
Charlotte, NC
Only used this twice after building it in February. I haven't lost interested in brewing, I'm looking to sell because this amount is just to much for me to drink. Below is a FULL breakdown of everything, but here are some quick notes. There is a lot to list, if i miss something or you have any question feel free to contact me. Everything was bought NEW and has 2 uses on it.
$3,500 OBO
The whole setup is semi-permanently mounted to the stand. Stand can go with the system or I can keep it, price does not change. The system is currently as is in the pictures and fully operational. No leaks, problems, scratches. For anyone picking up I would be happy to show the system working.
This is going to get wordy,
HLT
1 10 gallon Anvil Brew Kettle w/ dip tube
1 8" Coil with 2 bends 50' x 3/8" x .035 OD Tubing 304/304L
2 Pull Through Solderable 1/2" Compression
2 Stainless Ball Valve - 1/2" FPT Full Port
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Stainless Ball Valve - 1/2" FPT Full Port
1 Pull Through 1/2" bulkhead with integrated diptube
1 Closed nipple threaded 1/2"*NPT x 1"
1 Stainless steel "T" 1/2" FPT
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 1.5 inch, 1/2 NPT Thread
1 Camco 02955 4500W 240V Stainless Heater Element - Ultra Low Watt Density
1 Hot Pod Kettle Element Enclosure ETC4S - TC1.5" Enclosure w/clamp, gasket, and 1.5" TC Radiused Solder Flange
MLT
1 10 gallon Anvil Brew Kettle w/ dip tube
1 Anvil 10 gallon False Bottom
1 Elbow 1/2" NPT to 1/2" Barb
1 Stainless Ball Valve - 1/2" FPT Full Port
1 Pull Through 1/2" bulkhead
2 Closed nipple threaded 1/2"*NPT x 1"*
1 Stainless steel "T" 1/2" FPT
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 1.5 inch, 1/2 NPT Thread
Boil Kettle
1 10 gallon Anvil Brew Kettle w/ dip tube
1 Hop Stopper BK30
1 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 2.5 inch, M14 Thread
1 Camco 02955 4500W 240V Stainless Heater Element - Ultra Low Watt Density
1 Hot Pod Kettle Element Enclosure ETC4S - TC1.5" Enclosure w/clamp, gasket, and 1.5" TC Radiused Solder Flange
PUMPS (Direct Wire to Control Panel)
2 CHUGGER WORT PUMP WITH CENTER INLET STAINLESS HEAD
4 1/2" SS Camlock F style fitting Quick Disconnect
2 Stainless Ball Valve - 1/2" FPT Full Port
2 Stainless steel coupler 3/4" FPT x 1/2" FPT
HOSES
2 2ft length - High temperature food-grade silicone tubing (1/2" ID 3/4" OD)
3 5ft length - High temperature food-grade silicone tubing (1/2" ID 3/4" OD)
CONTROL BOX
1 16x16x8" Enclosure
2 40 amp SSR 3-32VDC input voltage, 90-480VAC output voltage
3 PID temperature controller, 1/16 DIN size, SSR output, 85-264VAC supply
1 MULTIFUNCTION TIMER, COUNTER, TACHOMETER
1 3 digit blue LED digital panel volt meter 700V AC, 5V DC supply 1 3 digit blue LED digital panel amp meter
1 Blue 22mm LED pilot light
1 Red 22mm LED pilot light
2 Green 22mm LED pilot light
2 Yellow 22mm LED pilot light
1 22mm buzzer, 115-120V AC/DC
6 2 position maintained selector switch
1 2 position maintained selector switch with key
1 3 position maintained selector switch
1 22mm red pushbutton, momentary
3 Contactor, 2 pole 40 A, 120V Coil
1 7A 250V fast blow glass fuse (4 extras included)
1 10A 8-pin 2-pole ice cube plug-in relay with 110-120VAC coil (8-pin relay socket)
1 Eaton D3PA2 Socket, Octal, 8 Pin
TOOLS
1 Pull-through Tool(included) https://www.brewhardware.com/product_p/ptbulkhead_tool.htm
Questions please contact me, no trades, cash only or Paypal.
FULL Gallery or Images
Only used this twice after building it in February. I haven't lost interested in brewing, I'm looking to sell because this amount is just to much for me to drink. Below is a FULL breakdown of everything, but here are some quick notes. There is a lot to list, if i miss something or you have any question feel free to contact me. Everything was bought NEW and has 2 uses on it.
$3,500 OBO
The whole setup is semi-permanently mounted to the stand. Stand can go with the system or I can keep it, price does not change. The system is currently as is in the pictures and fully operational. No leaks, problems, scratches. For anyone picking up I would be happy to show the system working.
- (3) - 10 Gallon Anvil kettles, all fittings soldered on however the bottom fittings are weldless and come like that from Anvil.
- Stainless Steel Heating Elements
- 30A 240V Control panel
- (2) Chugger Pumps
- Hoses (2) 3ft and (3) 5ft
This is going to get wordy,
HLT
1 10 gallon Anvil Brew Kettle w/ dip tube
1 8" Coil with 2 bends 50' x 3/8" x .035 OD Tubing 304/304L
2 Pull Through Solderable 1/2" Compression
2 Stainless Ball Valve - 1/2" FPT Full Port
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Stainless Ball Valve - 1/2" FPT Full Port
1 Pull Through 1/2" bulkhead with integrated diptube
1 Closed nipple threaded 1/2"*NPT x 1"
1 Stainless steel "T" 1/2" FPT
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 1.5 inch, 1/2 NPT Thread
1 Camco 02955 4500W 240V Stainless Heater Element - Ultra Low Watt Density
1 Hot Pod Kettle Element Enclosure ETC4S - TC1.5" Enclosure w/clamp, gasket, and 1.5" TC Radiused Solder Flange
MLT
1 10 gallon Anvil Brew Kettle w/ dip tube
1 Anvil 10 gallon False Bottom
1 Elbow 1/2" NPT to 1/2" Barb
1 Stainless Ball Valve - 1/2" FPT Full Port
1 Pull Through 1/2" bulkhead
2 Closed nipple threaded 1/2"*NPT x 1"*
1 Stainless steel "T" 1/2" FPT
2 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 1.5 inch, 1/2 NPT Thread
Boil Kettle
1 10 gallon Anvil Brew Kettle w/ dip tube
1 Hop Stopper BK30
1 1/2" SS Camlock F style fitting Quick Disconnect
1 Liquid tight RTD sensor, 2.5 inch, M14 Thread
1 Camco 02955 4500W 240V Stainless Heater Element - Ultra Low Watt Density
1 Hot Pod Kettle Element Enclosure ETC4S - TC1.5" Enclosure w/clamp, gasket, and 1.5" TC Radiused Solder Flange
PUMPS (Direct Wire to Control Panel)
2 CHUGGER WORT PUMP WITH CENTER INLET STAINLESS HEAD
4 1/2" SS Camlock F style fitting Quick Disconnect
2 Stainless Ball Valve - 1/2" FPT Full Port
2 Stainless steel coupler 3/4" FPT x 1/2" FPT
HOSES
2 2ft length - High temperature food-grade silicone tubing (1/2" ID 3/4" OD)
3 5ft length - High temperature food-grade silicone tubing (1/2" ID 3/4" OD)
CONTROL BOX
1 16x16x8" Enclosure
2 40 amp SSR 3-32VDC input voltage, 90-480VAC output voltage
3 PID temperature controller, 1/16 DIN size, SSR output, 85-264VAC supply
1 MULTIFUNCTION TIMER, COUNTER, TACHOMETER
1 3 digit blue LED digital panel volt meter 700V AC, 5V DC supply 1 3 digit blue LED digital panel amp meter
1 Blue 22mm LED pilot light
1 Red 22mm LED pilot light
2 Green 22mm LED pilot light
2 Yellow 22mm LED pilot light
1 22mm buzzer, 115-120V AC/DC
6 2 position maintained selector switch
1 2 position maintained selector switch with key
1 3 position maintained selector switch
1 22mm red pushbutton, momentary
3 Contactor, 2 pole 40 A, 120V Coil
1 7A 250V fast blow glass fuse (4 extras included)
1 10A 8-pin 2-pole ice cube plug-in relay with 110-120VAC coil (8-pin relay socket)
1 Eaton D3PA2 Socket, Octal, 8 Pin
TOOLS
1 Pull-through Tool(included) https://www.brewhardware.com/product_p/ptbulkhead_tool.htm
Questions please contact me, no trades, cash only or Paypal.
FULL Gallery or Images