Recent content by weathejx

My first thought after the brew was "holy crap, I cut two hours off my brew day and didn't really have to monitor the process." I didn't set up the PID correctly, so the first 15-30 minutes of my mash was playing around with the temps and settings. I finally figured out that I needed to run...

Everything is inside the box. I haven't cleaned up the wiring yet, which is the main reason there isn't a picture of the inside. The fain is directly next to the SSR and heatsink, so it stays really cool. I did a 90 minute mash today with the pump running the entire time. The air coming...

Ok, I think this is everything. I kept pretty good track, the first number is how many I bought, then the item, then the cost, then the link where I bought it. I already had a heat exchanger, so I didn't include that in the price list. Notes: To save cost, you could probably lose the 4"...

The pump head is completely outside of the toolbox, so if it leaked, it would be outside. The toolbox isn't waterproof (no sealing gasket or anything), but will keep drips out. It's all connected to a GFCI spa panel, so if anything does go terribly wrong, the breaker will trip and I wont die.

I got 3 in there, but subsequently sold it.

After 6 months, I've finally got everything bought and built! Full Setup Tool Box I cut some corners (mainly the twist lock stuff) but ended up with pretty much exactly what I wanted. Many thanks to Kal for his help and amazing website, P-J for his designs, and the users here for...

I am using the RTDs on the same PID. Ill do as you suggest and calibrate on the 50mm, as it'll be taking the mash temp and the 4" is sitting in the boil. I guess I don't really need the 4", but since I drilled a hole in my kettle, it's staying for now.

(sorry for the cross post with DIY, but I wasn't getting any views/responses) I have the ever popular SYL-2352 and two RTD probes, a 4" and a 50mm and I've got them wired up to the quick disconnects - all from Auber. I was calibrating the PID and noticed that the probes read the...

I have the ever popular SYL-2352 and two RTD probes, a 4" and a 50mm and I've got them wired up to the quick disconnects - all from Auber. I was calibrating the PID and noticed that the probes read the temperature differently, to the tune of 4-5 degrees. The 4" is reading 32-33 and the...

I wasn't able to get to the back of my dryer, but I was able to plug in the (not connected to anything at this point) cord I'm going to be using. It didn't trip and I was able to test the voltage coming from the two hot legs and it looks like everything is working fine. Thanks for the...

Do you mean, "make sure the neutral bar isn't somehow touching the enclosure?" I will check when I get home.

I mean "Plugging the dryer into it without turning it on" basically, I plug the spa panel into the wall, okeydokey. As soon as I plug in the dryer, it trips. I haven't wired my control panel yet, so I don't really have anything else to plug in to it. I guess I could wrap the exposed...

I followed the P-Js 4 wire diagram, and the breaker trips as soon as I plug something into the outlet (like the dryer) even with no load. What am I doing wrong here? Please note that the neutral wire, from the breaker to the outlet, is green because I didn't have 10g white wire. Does it...

Ok, so I updated the wiring and put the contactor in front of the element plug and changed the yellow LED to a SW. Now, when the control box is plugged in, the hot bus is energized and the PID and Timer get power. The pump and elements are controlled by switches. I changed my e-stop to the...

So I spent some time in Visio properly designing my system. If you guys could double check my work before I put in my orders, that would be great! Questions: 1. As far as the wiring goes, it seems like a lot of people are using a contactor and a physical switch before the element, but...