Sorry triker, I didn't realize I wasn't getting notifications on this thread so only noticed your question just now.
Long story short is to just keep trying the firmware update on the BZ4 until it works, first making sure you have stable WiFi+Internet. Lots of the discussions suggest that this...
Eventually realized my firmware didn't actually update last night, and when the OTA update failed again tonight I got the apparently common error 5379. Old firmware was from April 2022. After following advice on the RAPT Users Group (Facebook) to fix the OTA update issue and get the update...
Further to my last post, none of my steps defined as "Go to next step when" = "I press a button on the device" are behaving this way. Same with waiting to reach the specified temp before starting the timer - the profile is just blasting through all of the steps without stopping. I've been...
Apologies if this Notification-related question has previously been answered - I did search this thread but didn't see an answer for my specific symptoms...
I've had my BZ4 for quite a while now but only just now decided to try using Alerts. I have a "real" profile I created as well as a...
I recently switched to a Brewzilla 35 with a steam condenser so that I can brew indoors with no condensation or smell issues. I love it! Except that it is very difficult to monitor boil rate (or remaining volume level, depending how you look at it) since everything is sealed. I installed an...
Is anyone else using flow meters and faucets with adjustable flow rate? And if so, do you find that the accuracy of the flow meter calibration varies depending on the flow rate?
I'm using these https://www.amazon.ca/gp/product/B07MY6XJKK/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
and...
fun4stuff, I would really appreciate a step-by-step for this. I was an early (Kickstarter) adopter of Smartthings and just happen to have a ST motion detector right above my kegerator, controlling the garage lights. Ideally I'd like the screensaver to put the monitor into powersave mode rather...
Whoo-hoo! Commented out that function declaration in beerListTableVerticle.php and it's working!!
Amazing that I can still find my way around in vi, given that I only use it about ever 8-10 years for a few minutes each time :rock:
Once again proving myself incapable of letting go of a puzzling challenge, I've now WinSCP'd in and found my way to /var/log/apache2/error.log - which is showing me that beerListTableVerticle.php is trying to redeclare DisplayEditShowColumn() which had already been declared in common.php - and...
So working backwards from finding the row in the database's table "config" (configName = "showVerticleTapList") and then searching for that through the code, I see that common.php uses that value to decide whether to include beerListTableVerticle.php versus the normal beerListTable.php. It...
Are there any tricks to using the "Show Tap List Direction" = Vertical mode in the RandR+ version? In my new install from a couple of days ago, when I try this option I get a mostly blank page (just the header and body, no tables whatsoever). I tried changing a couple of other settings that I...
I eventually found this article https://howtoraspberrypi.com/enable-mysql-remote-connection-raspberry-pi/ which describes how by default MySQL is configured to not allow external connections. I had to dig a bit deeper than this article stated (the bind setting limiting connections to only...
A typical MySQL database instance will accept connections on port 3306 and communicate over that port using the MySQL protocol. My default assumption is that rpints and phpmyadmin would be using that to connect to the database, and if I go into the database using phpmyadmin and check the...
Thanks to the wisdom and support from y'all here, I have everything installed and beers/kegs/taps configured, and my first flow sensor reading!! (but not yet calibrated - hopefully tonight...)
Anyone know how to connect to the MySql database from another computer via tools like MySQL Workbench...